Permits

Toronto Sign Districts: What Each District Allows (Chapter 694)

Toronto Sign Districts: What Each District Allows (Chapter 694)

Toronto sign districts set which signs a property can have and how large they can be. Chapter 694, the Toronto Sign By-law, creates 9 general sign districts and 8 special sign districts, and the Schedule A maps put every property in one of them. Find your sign district before you design a sign or apply for a sign permit, because every size limit in the review depends on it.

Our principal, Irteza Ahmed, P.Eng., worked at the City of Toronto as a building plans examiner and reviewed sign permit applications. Our Sign Code Check starts with the sign district, then lists the permitted sign types and the maximum sign face areas for your property.

What is a sign district in Toronto?

Section 694-19A of Chapter 694, the Toronto Sign By-law, establishes the sign districts, and Schedule A maps them. The City’s General Sign Inquiries page says each property gets a sign district based on its use and the surrounding area. Three rules apply in every district:

  • Street centre line. The district of a property extends to the centre line of each street that it abuts (694-19B).
  • Split properties. If a property is in two or more sign districts, the rules of the district where the sign is located apply (694-14B).
  • Changes. Section 694-19C lets the City update Schedule A after Council changes the Official Plan or zoning designation of a property. By-law 1517-2025 used it in December 2025 to redesignate many premises.

The 17 Toronto sign districts

The 9 general sign districts are R (Residential), RA (Residential Apartment), C (Commercial), CR (Commercial Residential), E (Employment), EIO (Employment Industrial Office), I (Institutional), U (Utility) and OS (Open Space).

The 8 special sign districts (SSD) are Downtown Yonge Street (DYS-SSD), Sankofa Square (SK-SSD), City Hall and Nathan Phillips Square (CHNPS-SSD), University Avenue (UA-SSD), Gardiner Gateway (GG-SSD), Chinatown (CT-SSD), Entertainment District (ED-SSD) and Woodbine (WB-SSD). Each SSD has its own rules in section 694-26 and in Schedule C.

By-law 1517-2025 renamed the Dundas Square Special Sign District (DS-SSD) to the Sankofa Square Special Sign District (SK-SSD). The consolidated Chapter 694 on the City website is dated June 3, 2024, and still shows the old name. Always check for amending by-laws after that date.

What each Toronto sign district allows

The table summarizes the first party sign rules in section 694-21. Each item has more conditions in the by-law. “Not listed” means that 694-21 does not list that sign type for the district.

District Ground sign Wall signs Projecting sign Electronic sign Section
R Schools, places of worship, hospitals, nursing homes and community centres only: 0.3 m² per metre of frontage, 5.0 m² max, 6.0 m high Home occupation sign 0.3 m²; the five uses above: 20% of the first storey wall Not listed Not listed 694-21A
RA 1.5 m², 2.0 m high 2.0 m² each, 3.0 m high, on a wall that faces a street Not listed Not listed 694-21B
C 0.3 m² per metre of frontage, 20.0 m² max, 3.5 m to 10.0 m high by frontage 20% of the first storey wall, 10% of the second storey wall 1.0 m², 1.0 m projection Yes, with conditions 694-21C
CR Same as C Same as C Same as C Not listed 694-21D
E 0.3 m² per metre of frontage, 15.0 m² max, 7.5 m high First storey only: 15% of the wall, 20% on an office building Not listed Yes, with conditions 694-21I
EIO Same as E Same as E Not listed Not listed 694-21E
I 0.3 m² per metre of frontage, 8.0 m² max, 6.0 m high First storey only: 20% of the wall Not listed Not listed 694-21F
U 3.0 m², 1.5 m high First storey only: 15% of the wall Not listed Not listed 694-21G
OS 3.0 m², or 1.0 m² for each 100 m of frontage if greater First storey only: 10% of the wall Not listed Not listed 694-21H

Three more rules change by sign district:

  • Logo signs on tall offices. The C, CR, E and EIO districts allow a logo wall sign on an office building of 10 or more storeys. It goes on the top storey, the mechanical penthouse or the parapet, with two signs at most.
  • Driveway signs. Every general district lists a directional ground sign at a vehicle entrance: 0.5 m², 1.5 m high, two at each entrance. In an R district, only the five uses above get one.
  • Window signs. A first party window sign needs no sign permit in any district except R and RA, if it covers 25% of the window or less and is not above the second storey (694-6A(8)). The limit is the third storey in the Chinatown SSD.

Electronic signs: C and E sign districts only

Among the general districts, section 694-21 lists first party electronic signs only in the C district (694-21C(7) and (8)) and the E district (694-21I(6) and (7)). The main conditions are:

  • One electronic sign on the premises, and a frontage of 100 m or more.
  • A distance of 60.0 m or more from any R, RA, CR, I or OS sign district.
  • Static and electronic static copy only, with each message shown for 3.0 minutes or less.
  • No residential occupancy on the premises. In a C district, the premises must also be a commercial plaza with 10 or more units.

Third party signs by sign district

Among the general districts, section 694-25 permits third party signs only in the C, CR, E and U sign districts. Some SSDs also permit them, for example the DYS-SSD (694-26B). Three general limits apply. A sign that does not meet them needs a third party sign variance.

  • Spacing. A third party sign must be 100.0 m or more from any other lawful third party sign, and 150.0 m for an electronic one (694-22D and E).
  • Heritage. A third party sign cannot go in a heritage conservation district or on a listed or designated heritage building, unless the chapter expressly permits it (694-22C).
  • Restricted areas. Section 694-24A bans them in listed areas, for example within 400 m of parts of the Gardiner Expressway.

How to find your sign district and confirm the rules

  1. Open the City’s SignView mapping tool and type the address.
  2. Record the sign district code and the name of any SSD.
  3. Check Schedule B of Chapter 694 for a Signage Master Plan or an area-specific amendment on the property.
  4. Read 694-20 and 694-21 for first party signs, 694-22 and 694-25 for third party signs, or 694-26 and Schedule C for an SSD.
  5. Compare each sign with each limit. Our sign permit drawings show these dimensions for the examiner.

If the sign does not comply, the City’s First Party Sign Permit page tells you to start with a Preliminary Project Review.

When your sign district does not allow your sign

The City can grant a sign variance only if the sign belongs to a sign class (first party or third party) that the sign district permits (694-30A(1)). A change to the sign district of a property needs a by-law amendment under 694-31A(3). A variance for three or more signs, or on a premises with an approved Signage Master Plan, needs a Signage Master Plan application (694-30B(2)). See our guides on Toronto sign variances and the Signage Master Plan in Toronto.

Toronto is reviewing its Sign By-law

The City started a Sign Bylaw Review. The survey is open from November 18 to December 9, 2026. The review covers permanent signs on private property, permits, variances and enforcement. The current Sign By-law stays in effect during the review.

Need help with your Toronto sign district?

Send us the address, photos of the building and the sign artwork. We confirm the sign district, check each sign against Chapter 694, and tell you if you need a sign permit only, a variance or a Signage Master Plan. We reply within one business day. Contact us or see our sign permit service.

Need help with your sign permit?

Tell us about your project and we'll reply within one business day with next steps and a quote.

See our sign permit services.